1. 毕业设计（论文）的内容和要求
(I) Design basis1, Project overviewThis project is a practical application project of a teaching building in Nanjing, Jiangsu. The single-story building area of this building is about 1049.4m2, the main body is three spans and seven floors, and the building area is about 7345.8m2. Multi-layer reinforced concrete frame structure is required. Under normal circumstances, the reasonable design service life of this project is 50 years. The general plan of the project and the layout of the standard layer column network are shown in the attached drawing of the task book.2, Meteorological information Base air pressure:0.50kN/m2 Basic snow pressure:0.40kN/m2 3, Engineering geological information (1) The geotechnical engineering survey report was provided by a certain architectural design institute. According to the survey report, the proposed site has a flat terrain with a surface filled with miscellaneous soil, the following silty clay and clay; no liquefied soil layer distribution, stable groundwater level burial depth 1.65 -2.14m, non-corrosive to reinforced concrete.(2) Foundation form: According to the engineering geological characteristics of the site and the structural load characteristics of the proposed building, it is recommended to use an independent foundation of reinforced concrete under the column, with ② layers of silty clay as the supporting layer.(3) For detailed surveys, please refer to the materials in this mission statement. 4, Structural and site seismic effects (1) This project is a multi-layer frame structure, and the safety level of the building structure is Grade II.(2) The seismic fortification intensity of the proposed site is 7 degrees, the design basic seismic acceleration value is 0.10g, and the design seismic grouping is the first group.(3) Engineering site category II.(4) According to the "Classification Standard for Seismic Fortification of Construction Engineering", this project is a Class C building.5, Load valueAdopted according to "Building Structure Load Code" GB5009-2001.6, Construction technical conditions: This project was undertaken by a construction engineering company, with complete equipment and good technology.7, Material supply: Three materials and general materials can be supplied in a timely manner as planned.8, Water, electricity supply: Guaranteed by the construction unit.(II) Design content and requirementsAccording to the general plan and design requirements provided, the main architectural design, the upper frame structure and basic calculation, component design, node construction design, construction drawing and so on are completed.The specific requirements are as follows:1, the architectural partAccording to the general plan provided and the standard layer column network layout, the architectural design is carried out, and the corresponding construction drawing is completed.2, structural part2.1 Structural calculations(1) To carry out structural arrangement, the component cross-sectional size and material strength grade selection.(2) Design calculations for the following structures and components:① Hand count a horizontal framePermanent load and its effects; variable living load (taking into account adverse placement) and its effects; wind load and its effects; seismic effects and effects; and other software calculations.② Internal force analysis, internal force combination and beam column cross-section design, hand-counted bottom, standard layer and top layer;③ The current pouring floor panel: choose a standard layer hand calculation, the rest of the software calculation.④ Stair design: choose a stairwell hand calculation, the rest of the software calculation.⑤ Basic design: complete the basic selection, layout, basic corresponding design calculation.(3) Draw the construction drawing (see after the detailed requirements).(4) Structural design calculation specification writing requirements.2.2 Calculation cookbook preparationThe detailed description of architectural design, structure layout basis, component selection, material determination, determination of the calculation of horizontal frame, internal force calculation and combination, frame displacement calculation, component cross-section al-design, banding sketch, requires the drawing of the main node structure diagram (non-flat representation) and related structural description; The calculation and design of the infrastructure, the calculation of force results within the horizontal framework of the software and the analysis of the results of hand calculation, a brief construction description. In addition, the design calculation book should also include Chinese and English abstracts, catalogues, body, references, appendices and other basic content, and meet the requirements of the graduation design calculation specification, clear level, appropriate expression, focus, and not less than 80 pages.(1) The design calculation book should include Chinese and English abstracts, catalogues, body, references, thanks and other basic contents, and meet the requirements of the graduation design calculation specification, the level is clear, the expression is appropriate, the focus is outstanding.(2) Detail the basis of the building plan, architectural design characteristics and key architectural design parameters;(3) The basis of structure arrangement, the selection of components, the determination of materials;(4) To determine the calculation sketch of the horizontal frame, the calculation and combination of internal forces, and the calculation of the horizontal displacement of the framework.(5) component cross-sectional design, rib profile, typical node design, requires the drawing of the main node construction diagram (non-flat representation), as well as the structure description;(6) The design calculation of the typical stair structure;(7) The design and calculation of the infrastructure;(8) The computer calculation content closely follows the corresponding hand-counted content, and the software calculation results and hand calculation results for comparative analysis;2.3 Drawing of construction drawings (see after detailed requirements)3, construction organization designThe preparation of the design book of the construction organization should include: the project overview, the management organization, the construction plan and technical measures, the construction schedule (crossroad map), the construction preparation, the quality assurance measures, the safe and civilized construction measures, and the construction plan.4. Foreign translationTranslation of foreign materials of not less than 10,000 printed symbols. The original text and translation of the foreign language as a graduation design necessary accessory, individually bound into a book, as graduation design materials and other achievements together with the submission.
2. 参考文献
[1] Su J01-2005. Construction instructions [S].[2] Su J9503-J04-2005. Roof building structure, balcony, stairs, bathroom, sink [S].[3] Su J9508. Outdoor Engineering [S].[4] Su J05-2005. Stairs [S].[5] Su J11-2006. Aluminum alloy doors and windows [S].[6] Su J09-2005. Lightweight partition wall, wall body, floor deformation joint [S].[7] Architectural Design Data Collection Editorial Committee. Architectural Design Data Collection (8) Second Edition [M]. Beijing: China Construction Industry Press, 1996.[8] Architectural Design Data Collection Editorial Committee. Architectural Design Data Collection (9) Second Edition [M]. Beijing: China Construction Industry Press, 1997.[9] Edited by Editorial Committee of Architectural and Structural Data Collection. Architectural and Structural Data Collection (Upper and Lower) Second Edition [M]. Beijing: China Construction Industry Press, 2009.[10] GB50009-2001. Building Structure Load Specification [S].[11] GB50010-2010. Code for design of concrete structures [S].[12] GB50011-2010. Code for seismic design of buildings [S].[13] GB50003-2011. Code for design of masonry structures [S].[14] GB50007-2002. Code for design of building foundation [S].[15] 03G101-1. The overall representation method of the concrete structure construction drawing. Drafting rules and structural details [S].[16] Architectural data set (upper and lower) [Z]. Beijing: China Construction Industry Press.[17] Edited by Xu Xiuli. Design of concrete frame structure [M]. Beijing: China Construction Industry Press. 2008.8.[18] Liang Xingwen, editor of Shi Qingxuan. Guidance for graduation design of civil engineering specialty [M]. Beijing: Science Press, 2005.[19] Dong Jun, Zhang Weiyu, Gu Jianping. Graduation Design Guide for Civil Engineering Specialty-Building Construction Volume [M]. Beijing: China Water Resources and Hydropower Press, March 2002[20] Edited by Zhou Guoxing, Guide to Graduation Design of Housing Structures [M]. China Construction Industry Press, 2004.[21] Li Hongnan, Cui Xiguang, Zou Chaoying, etc. Structural design of multi-storey and high-rise buildings [M]. Beijing: China Construction Industry Press, 1998.[22] Zhang Weibin, chief editor. Doubts and engineering examples of multistory and high-rise reinforced concrete structure design [M]. Beijing: China Construction Industry Press, 2005.
以上是毕业论文任务书，课题毕业论文、开题报告、外文翻译、程序设计、图纸设计等资料可联系客服协助查找。
